How to Make a Balloon Obama Parody



We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

Here are the supplies- warning this is not a beginner design. some of the techniques may be challenging for novices

Inflate 1 mocha, 2 black, & 1 chocolate brown leaving a 4" tail. Be sure to give it a good burp. Also inflate the white balloon to about 11". Cut the other mocha balloon in half and tie off end.

Inflate the two half mocha balloons to about 5"

Inflate the white 5" balloon to about 1" and put just over a puff of air in the red one

Take the mocha balloon and twist off a 1- 1.5" bubble. This will be the ear... Since its a balloonicature parody of Obama it's ok for the ears to be a little big

Pinch twist the bubble

Make a 4" bubble and then a second 1-1.5" bubble

Pinch twist this bubble as well for the second ear and anchor point

Double back and twist into ear at other side

Make the next few bubbles softer so they won't pop from the pressure. There should be 5 bubbles total.

Another view of all 5 bubbles

And another angle.... After making sure that balloon is secure, cut off extra piece from just above the ear. Do not discard- you will need for next step

Inflate a small bubble at the nipple end of the scrap and tie close to bubble, leaving tail intact. Set aside

Take chocolate brown balloon

Tie in to ear from nozzle- this will become hair.

Go from one side to the other and twist into ear

Once more

And third times the charm

Cut off excess

Like so...

21

Take small white balloon and mocha scrap

22

Twist white balloon in half using nozzle to secure

23

And tie to mocha bubble

24

Like so... Leave tails attached

25

Put the eyes and nose between the forehead and lips

26

Like this... Be sure to pull out the tail from the nose as this is how you will attach the head

27

Now take the two black balloons

28

Twist off a 9" section on each balloon and give it a little bend.

29

And twist them together

30

Now make a small set of bubbles under the arms

31

And pinch twist them

32

Twist off 9" bubbles from both balloons and twist together

33

And twist off small bubbles under the body

34

Squeeze together and pinch twist

35

Like so..

36

Twist basic loops at base of legs. It's ok if feet are a little big- he's got big shoes to fill ;-)

37

Do the same on both sides

38

Here's the body base

39

Take white balloon and twist off a small bubble

40

And make a second one the same size and twist together

41

And pinch twist them

42

Attach to body

43

Like so

44

And bring down to bottom, wrap around a few times and cut off excess after making sure its secure

45

Like this

46

Now take the little mocha pieces

47

And make a little dog head (.5" bubble, and 2 1" bubble twisted together )

48

Like so

49

Do the same on the other hand

50

Like this

51

Make sure the balloon is secure and then cut off excess of both balloons

52

And attach it to arm using nozzle of black balloon

53

Like this

54

Cut off the extra bits and do the same to the other arm

55

Now put on the head using the tail from the mocha

56

Like this (you kind of sew it in)

57

We're getting there. Time for details...

58

Take the little red balloon and stuff it in his mouth

59

And add a red balloon scrap for the tie

60

Twist the feet together and position hips to help him stand

61

And there is the 44th presidential parody Copyright Balloon Utopia tm 2012. Www.balloonutopia.com

62

Copyright Balloon Utopia tm 2012. Www.balloonutopia.com


Watch the video: President Obama Surprises Joe Biden With Medal of Freedom


Comments:

  1. Ioseph

    I don't believe you

  2. Deylin

    It is well said.



Write a message


Previous Article

How to make warm cabbage slaw

Next Article

How to Teach Your Dog to Spin